Anritsu S251C Manual do Utilizador descarregar pdf (Página 5)

CONTROL BYTE DESCRIPTIONS ......................................................................................................... 2

Setup System - Control Byte #1 (01h)..................................................................................................... 2

Set Site Master Frequency - Control Byte #2 (02h)................................................................................ 2

Select Measurement Mode - Control Byte #3 (03h)................................................................................ 2

Set Site Master Scale - Control Byte #4 (04h)........................................................................................ 3

Set Site Master Marker - Control Byte #5 (05h)..................................................................................... 4

Set Segmented Limit Lines - Control Byte #6 (06h)................................................................................ 4

Set DTF Parameter - Control Byte #7 (07h) .......................................................................................... 5

Set Time/Date - Control Byte #8 (08h)................................................................................................... 6

Set Reference Number - Control Byte #9 (09h) ...................................................................................... 6

Serial Port Echo On/Off - Control Byte #10 (0Ah)................................................................................. 6

Single Sweep Mode On/Off - Control Byte #11 (0Bh) ............................................................................ 7

Watch-Dog Timer On/Off - Control Byte #12 (0Ch) .............................................................................. 7

Sequence Site Master Calibration - Control Byte #13 (0Dh) ................................................................. 7

Set Site Master Data Points - Control Byte #14 (0Eh) ........................................................................... 8

Set Site Master Limit Beep Status - Control Byte #15 (0Fh) .................................................................. 8

Store Sweep Trace - Control Byte #16 (10h).......................................................................................... 8

Recall Sweep Trace - Control Byte #17 (11h) ........................................................................................ 9

Save System Setup - Control Byte #18 (12h) ........................................................................................ 11

Recall System Setup - Control Byte #19 (13h)...................................................................................... 12

Query System Status - Control Byte #20 (14h)..................................................................................... 12

Trigger Self-Test - Control Byte #21 (15h)........................................................................................... 14

Read Fail Counters - Control Byte #22 (16h) ...................................................................................... 15

Clear Fail Counters - Control Byte #23 (17h)...................................................................................... 15

Query Trace Names - Control Byte #24 (18h)......................................................................................15

Delete Sweep Trace - Control Byte #25 (19h)...................................................................................... 16

Upload Sweep Trace - Control Byte #26 (1Ah).................................................................................... 16

Query Sweep Memory - Control Byte #27 (1Bh).................................................................................. 18

Select Printer Type - Control Byte #30 (1Eh)....................................................................................... 18

Select DTF Windowing - Control Byte #31 (1Fh) ................................................................................ 19

Set Trace Math - Control Byte #32 (20h) ............................................................................................. 19

Set RF Source Mode Frequency - Control Byte #33 (21h)................................................................... 20

Set Trace Overlay - Control Byte #34 (22h)......................................................................................... 20

Get Options - Control Byte #37 (25h) .................................................................................................. 20

Query Power Level - Control Byte #39 (27h)....................................................................................... 20

Set Power Monitor Unit - Control Byte #40 (28h)................................................................................ 21

Relative Mode On/Off - Control Byte #41 (29h)...................................................................................21

Offset Mode On/Off - Control Byte #42 (2Ah)...................................................................................... 21

Zero Mode On/Off - Control Byte #43 (2Bh)........................................................................................ 22

Trigger Sweep - Control Byte #48 (30h) .............................................................................................. 22

Check Battery Status - Control Byte #50 (32h) .................................................................................... 22

Set Marker Peak - Control Byte #51 (33h)........................................................................................... 22

Set Marker Valley - Control Byte #52 (34h)......................................................................................... 23

Set Bias Tee Function - Control Byte #54 (36h)................................................................................... 23

Set Site Master Single Limit - Control Byte #55 (37h) ......................................................................... 23

Automatically Save Runtime Setup - Control Byte #64 (40h)............................................................... 24

Enter Remote Mode - Control Byte #69 (45h)......................................................................................24

Enter Remote Mode Immediately - Control Byte #70 (46h) ................................................................. 24

Write Custom Cable - Control Byte #80 (50h) .....................................................................................25

Recall Custom Cable - Control Byte #81 (51h)....................................................................................25

Set Site Master Marker (Peak/Valley) - Control Byte #129 (81h)........................................................ 25

Set Baud Rate - Control Byte #197 (C5h)............................................................................................. 26

Set Language – Control Byte #198 (C6h)............................................................................................. 26

Query Time - Control Byte #208 (D0h)................................................................................................ 26

Read Main Serial Number - Control Byte #221 (DDh) ........................................................................ 27

Read ASCII Serial Number - Control Byte #225 (E1h) ........................................................................ 27

Exit Remote Mode - Control Byte #255 (FFh)......................................................................................27

Parameter Definitions .......................................................................................................................... 28

1 2 3 4 5 6 7 8 9 10 ... 33 34

Comentários a estes Manuais

Sem comentários

Anritsu S251C Manual do Utilizador Página 5

Comentários a estes Manuais